This is a list of ISO standards that are discussed in Wikipedia articles. For a list of all the more than 16,000 ISO standards (as of 2007), see the ISO Catalogue. About 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC1) have been made freely/publicly available.
Contents |
ISO 1–ISO 999
- ISO 1 Standard reference temperature for geometrical product specification and verification
- ISO 3 Preferred numbers
- ISO 7 Pipe threads where pressure-tight joints are made on the threads
- ISO 9 Information and documentation – Transliteration of Cyrillic characters into Roman characters – Slavic and non-Slavic languages
- ISO 16:1975 Acoustics – Standard tuning frequency (Standard musical pitch)
- ISO 31 Quantities and units
- ISO 68-1 Basic profile of metric screw threads
- ISO 216 paper sizes, e.g. the A4 paper size
- ISO 226 Phon based on Fletcher-Munson curves
- ISO 226:2003 Phon based on newer Equal-loudness contours
- ISO 233:1984 Transliteration of Arabic characters into Roman characters
- ISO 233-2:1993 Transliteration of Arabic characters into Roman characters – Part 2: Arabic language – Simplified transliteration
- ISO 259:1984 Documentation – Transliteration of Hebrew characters into Roman characters
- ISO 262 Selected metric-screw-thread sizes for screws, bolts, and nuts
- ISO 639 Codes for the representation of names of languages
- ISO/IEC 646 internationalized 7 bit ASCII variants
- ISO 657 Hot-rolled steel sections
- ISO 668 Specification for Shipping Containers
- ISO 690 bibliographic references
- ISO 732 Photography – 120-size and 220-size films – Dimensions
- ISO 838 Standard for punching filing holes into paper
- ISO 843:1997 Conversion of Greek characters into Roman characters
- ISO 999 Guidelines for the content, organization, and presentation of indexes
ISO 1000–ISO 9999
- ISO 1000 SI units and recommendations for the use of their multiples and of certain other units
- ISO 1007 135 film format
- ISO/IEC 1539 Fortran programming language
- ISO 1629 Establishes a system of terms and nomenclature for polymers
- ISO/IEC 2022 Information technology: Character code structure and extension techniques
- ISO 2108 International standard book numbering (ISBN)
- ISO 2145 Numbering of divisions and subdivisions in written documents
- ISO 2171 Cereals and milled cereal products – Determination of total ash
- ISO 2281 Water-resistant watches
- ISO 2533 Standard Atmosphere
- ISO 2709 Format for information exchange (e.g. MARC)
- ISO 3029 126 film format
- ISO 3082 Iron ores – Sampling and sample preparation procedures
- ISO 3103 Method of brewing tea for the purpose of sensory tests
- ISO 3166 codes for countries and subdivisions
- ISO 3166-1 codes for country and dependent area names, first published in 1974
- ISO 3166-1 alpha-2 two-letter country codes
- ISO 3166-1 alpha-3 three-letter country codes
- ISO 3166-1 numeric
- ISO 3166-2 principal subdivisions of a country or dependent area.
- ISO 3166-3 superseded ISO 3166-1 codes, first published in 1998.
- ISO 3166-1 codes for country and dependent area names, first published in 1974
- ISO 3297 International standard serial number (ISSN)
- ISO 3506 Mechanical properties of corrosion-resistant stainless steel fasteners.
- ISO 3602 Romanization of Japanese
- ISO 3632 Quality of Saffron
- ISO 3864 Safety labels
- ISO 3901 International Standard Recording Code (ISRC)
- ISO 3977 Design and procurement standards for gas turbine system applications
- ISO 4157 Subdivision of construction works
- ISO 4217 Currency codes
- 8-bit code for information interchange
- ISO 5167 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full
- ISO 5167-1 Part 1: General principles and requirements
- ISO 5167-2 Part 2: Orifice plates
- ISO 5167-3 Part 3: Nozzles and Venturi nozzles
- ISO 5167-4 Part 4: Venturi tubes
- ISO 5218 Representation of human sexes
- ISO 5775 Bicycle tyres and rims
- ISO 5800 Photographic Film speed
- ISO 5964 Guidelines for the Establishment and Development of Multilingual Thesauri
- ISO 6166 structure of an International Securities Identifying Number (ISIN)
- ISO 6344 Coated abrasives – Grain size analysis
- ISO 6344-1 Part 1: Grain size distribution test
- ISO 6344-2 Part 2: Determination of grain size distribution of macrogrits P12 to P220
- ISO 6344-3 Part 3: Determination of grain size distribution of microgrits P240 to P2500
- ISO 6429 Information technology: Control functions for coded character sets
- ISO 6438 Documentation – African coded character set for bibliographic information interchange
- ISO 6709 Standard representation of latitude, longitude and altitude for geographic point locations
- ISO 6946 Building components and building elements - Thermal resistance and thermal transmittance - Calculation method
- ISO 7001 Public Information Symbols
- ISO 7098 Romanization of Chinese
- ISO 7372 Trade data interchange
- ISO/IEC 7501-1:1997 Identification cards – Machine readable travel documents (Part 1: Machine readable passport; Part 2: Machine readable visa; Part 3: Machine readable official travel documents)
- ISO 7736 Car radio installation space
- ISO 7810 Standards for financial cards (credit and debit cards)
- ISO 7811 Recording technique on identification cards
- ISO 7816 Smartcards
- ISO/IEC 7942 Graphical Kernel System
- ISO 8090 Cycles – Terminology
- ISO 8373 Manipulating Industrial Robots – Vocabulary
- ISO 8501-1 Preparation of steel substrates before application of paints and related products
- ISO 8555 Environmental management systems.
- ISO 8583 Financial transaction card originated messages – Interchange message specifications
- ISO 8583-1 Part 1: Messages, data elements and code values
- ISO 8583-2 Part 2: Application and registration procedures for Institution Identification Codes (IIC)
- ISO 8583-3 Part 3: Maintenance procedures for messages, data elements and code values
- ISO 8601 Date and time representation
- ISO/IEC 8613 Open Document Architecture
- ISO/IEC 8632 Computer Graphics Metafile
- ISO 8651 Graphical Kernel System language bindings
- ISO/IEC 8652: Information technology – Programming languages – Ada
- ISO 8805 Graphical Kernel System for Three Dimensions and the C language bindings are ISO 8806.
- ISO 8806-4 Graphical Kernel System for Three Dimensions, C language bindings
- ISO 8807: Language Of Temporal Ordering Specification (LOTOS)
- ISO/IEC 8824 Abstract Syntax Notation One (ASN.1)
- ISO/IEC 8825 ASN.1 Encoding Rules
- ISO 8859 8-bit coded character sets
- ISO 8859-1 Latin-1
- ISO 8859-2 Latin-2
- ISO 8859-3 Latin-3 or "South European"
- ISO 8859-4 Latin-4 or "North European"
- ISO 8859-5 Cyrillic
- ISO 8859-6 Arabic
- ISO 8859-7 Greek
- ISO 8859-8 Hebrew
- ISO 8859-9 Latin-5
- ISO 8859-10 Latin-6, rearrangement of 8859-4
- ISO 8859-11 Thai
- ISO 8859-13 Latin-7 or "Baltic Rim"
- ISO 8859-14 Latin-8 or "Celtic"
- ISO 8859-15 Latin-9, revision of 8859-1
- ISO 8859-16 Latin-10 South-Eastern European languages and others
- ISO 8879 Standard Generalized Markup Language (SGML)
- ISO 9000 Quality management system in production environments
- ISO 9001 Quality management
- ISO 9069 SGML support facilities — SGML Document Interchange Format (SDIF)
- ISO/IEC 9075 SQL
- ISO 9126 Software quality model
- ISO 9141 Network interconnection of computers in a vehicle
- ISO 9241 Ergonomic requirements for office work with visual display terminals
- ISO 9362 Bank Identifier Code or BIC system
- ISO 9407 Shoe sizes
- ISO 9564 Banking — Personal Identification Number (PIN) management and security (in ATM and POS systems)
- ISO/IEC 9579 Remote database access for SQL
- ISO 9592, ISO 9593 PHIGS (Programmer's Hierarchical Interactive Graphics System)
- ISO 9660 CD-ROM file system
- ISO 9869 Thermal insulation - Building elements - In-situ measurements of thermal resistance and thermal transmittance
- ISO 9899 C programming language
- ISO/IEC 9945 Portable Operating System Interface (POSIX)
- ISO 9984 Conversion of Georgian characters into Roman characters
- ISO 9985 Conversion of Armenian characters into Roman characters
- Financial transaction cards - Security architecture of financial transaction systems using integrated circuit cards
- ISO 9999 Technical aids for persons with disabilities. Classification and terminology
ISO 10000–ISO 19999
- ISO 10006 Quality management – Guidelines to quality in project management
- ISO 10007 Quality management – Guidelines for configuration management
- ISO/IEC 10021 Message Oriented Text Interchange Systems (MOTIS)
- ISO/IEC 10026 Open Systems Interconnection
- ISO 10077 Thermal performance of windows, doors and shutters - Calculation of thermal transmittance
- ISO/IEC 10089 Information technology; 130 mm rewritable optical disk cartridge for information interchange - 650 MB per cartridge
- ISO 10160 Interlibrary Loan Application Service Definition - defines terminology used in interlibrary loan
- ISO 10161 Interlibrary Loan Application Protocol
- Document Style Semantics and Specification Language (DSSSL)
- Financial transaction cards — Security architecture of financial transaction systems using integrated circuit cards
- ISO 10211 Thermal bridges in building construction — Heat flows and surface temperatures — Detailed calculations
- ISO 10279 BASIC programming language
- ISO 10303 Industrial automation systems and integration – Product data representation and exchange. Known as STEP, STandard for the Exchange of Product data
- ISO 10383 Securities and related financial instruments - Codes for exchanges and market identification (MIC)
- ISO 10487 Connections for passenger car stereos
- ISO 10628 Flow diagrams for process plants
- ISO 10646 Universal Character Set (equivalent to Unicode's character set)
- ISO 10664 Hexalobular internal driving feature for bolts and screws – Torx screw head
- ISO 10957 Information and documentation – International Standard Music Number (ISMN)
- ISO 10962 Securities and related financial instruments - Classification of Financial Instruments (CFI code)
- ISO 11064 Ergonomic Design of Control Centres
- ISO 11062-1:2000 Part 1: Principles for the design of control centres
- ISO 11062-2:2000 Part 2: Principles for the arrangement of control suites
- ISO 11062-3:1999 Part 3: Control room layout ISO 11064-3:1999/Cor 1:2002
- ISO 11062-3:2004 Part 4: Layout and dimensions of workstations
- ISO 11062-3:2005 Part 6: Environmental requirements for control centres
- ISO/IEC 11172 MPEG-1
- ISO 11170:2003 Hydraulic fluid power - Filter elements - Sequence of tests for verifying performance characteristics
- ISO/IEC 11179 Information Technology –- Metadata Registries (MDR)
- ISO/IEC 11179-1:2004 Part 1: Framework
- ISO/IEC 11179-2:2005 Part 2: Classification
- ISO/IEC 11179-3:2003 Part 3: Registry metamodel and basic attributes
- ISO/IEC 11179-4:2004 Part 4: Formulation of data definitions
- ISO/IEC 11179-5:2005 Part 5: Naming and identification principles
- ISO/IEC 11179-6:2005 Part 6: Registration
- ISO 11180 Postal addressing
- ISO/IEC 11404:1996 Language-independent datatypes (See also General purpose datatypes)
- ISO 11521 Replaced by ISO 15022
- ISO/IEC 11578:1996 Information technology -- Open Systems Interconnection -- Remote procedure call (RPC)
- ISO 11783 aka. IsoBus - J1939-based communication protocol for the agriculture industry.
- ISO/IEC 11801 Information technology – Generic cabling for customer premises
- ISO 11898 Road vehicles -- Controller area network (CAN)
- ISO 12006 Building construction. Organization of information about construction works.
- ISO 13239 High-level data link control (HDLC) procedures
- ISO/IEC 13249 SQL multimedia and application packages
- ISO/IEC 13250 Topic map
- ISO 13346 Volume and file structure of write-once and rewritable media, which UDF is based on.
- ISO 13370 Thermal performance of buildings - Heat transfer via the ground - Calculation methods
- ISO 13406 Ergonomic requirements for work with visual displays based on flat panels
- ISO 13406-1:1999 Part 1: Introduction
- ISO 13406-2:1002 Part 2: Ergonomic requirements for flat panel displays
- ISO 13407:1999 Human-centred design processes for interactive systems
- ISO 13450 110 film format
- ISO 13485:2003 Comprehensive management system for the design and manufacture of medical devices.
- ISO 13490 Information technology: Volume and file structure of read-only and write-once compact disk media for information interchange
- ISO 13567/1 to 3 Technical product documentation; Organization and naming of layers for Computer-aided design (CAD)
- Information Technology – Z Formal Specification Notation – Syntax, Type System and Semantics
- ISO 13616 Bank Account Numbers (IBAN)
- ISO 13849-1 Safety of machinery, Safety related parts of control systems, General principles for design
- ISO/IEC 13818 MPEG-2
- ISO 14000 Environmental Management Standards in production environments
- ISO 14001 Environmental Management
- ISO 14064 Greenhouse Gases
- ISO 14443 contactless smart ? cards aka RFID
- ISO/IEC 14496 MPEG-4
- ISO 14644 Cleanrooms and associated controlled environments
- ISO-14644-1 Classification of Air Cleanliness
- ISO-14644-2 Testing and Monitoring to prove Compliance
- ISO-14644-3 Metrology & Test Methods
- ISO-14644-4 Design, Construction and Start-up
- ISO-14644-5 Operations
- ISO-14644-6 Vocabulary
- ISO-14644-7 Separative Devices
- ISO-14644-8 Classification of Airborne Molecular Contamination
- ISO-14644-9 Clean Surfaces
- ISO 14651 Information technology: International string ordering and comparison
- ISO 14698
- ISO-14698-1 Bio-contamination Control - General Principles
- ISO-14698-2 Evaluation & Interpretation of Bio-contamination Data
- ISO-14698-3 Measuring the efficiency of processes of cleaning & disinfection
- ISO 14750 Information technology – Open Distributed Processing – Interface Definition Language
- ISO/IEC 14755 Input methods to enter unicode characters from ISO/IEC 10646
- ISO 14915 Software ergonomics for multimedia user interfaces
- ISO 14915-1:2002 Part 1: Design principles and framework
- ISO 14915-2:2003 Part 2: Multimedia navigation and control
- ISO 14915-3:2002 Part 3: Media selection and combination
- ISO/IEC 14977 Extended Backus-Naur Form (EBNF)
- ISO/IEC 14882 Programming Languages — C++
- ISO 15000 Electronic business eXtensible Markup Language ebXML
- ISO 15000-1:2004 Part 1: Collaboration-protocol profile and agreement specification (ebCPP)
- ISO 15000-2:2004 Part 2: Message service specification (ebMS)
- ISO 15000-3:2004 Part 3: Registry information model specification (ebRIM)
- ISO 15000-4:2004 Part 4: Registry services specification (ebRS)
- ISO 15000-5:2005 Part 5: ebXML Core Components Technical Specification, Version 2.01(ebCCTS)
- ISO 15022 Securities: Scheme for messages(Data Field Dictionary)
- ISO 15099 Thermal performance of windows, doors and shading devices – Detailed calculations
- ISO 15189 Medical laboratories – Particular requirements for quality and competence
- ISO 15288 Systems engineering – System life cycle processes
- ISO/IEC 15291: Information technology – Programming languages – Ada Semantic Interface Specification (ASIS)
- ISO/IEC 15408 Common Criteria – Evaluation Criteria for Information Technology Security
- ISO/IEC 15434 2D Data Matrix barcode
- ISO/IEC 15444 JPEG 2000
- ISO/IEC 15445:2000 ISO HTML, a subset of Hypertext Markup Language (HTML) 4
- ISO/IEC 15504 Framework for the assessment of software processes, also known as SPICE (Software Process Improvement and Capability Determination).
- ISO 15614-13:2002 Specification and qualification of welding procedures for metallic materials-Welding procedure test-
- ISO 15686 Service life planning for constructive works in 10 parts
- ISO 15693 Transponders
- ISO 15706 International Standard Audiovisual Number
- ISO 15707 International Standard Musical Work Code
- ISO 15836 The Dublin Core metadata element set
- ISO 15897 Standard for the registration of new POSIX locales and POSIX charmaps
- ISO 15924 Codes for the representation of names of scripts
- ISO 15930 Portable Document Format PDF
- ISO/IEC 15948:2003. Portable Network Graphics PNG
- ISO/IEC 16500 Generic Digital Audio-Visual Systems DAVIC
- ISO 16701:2003 Ergonomics of human-system interaction, Guidance on accessibility for human-computer interfaces
- ISO/IEC 16262. ECMAScript
- ISO 16750 Road vehicles -- Environmental conditions and testing for electrical and electronics equipment.
- ISO/TS 16949 Quality management systems -- Particular requirements for the application of ISO 9001:2000 for automotive production and relevant service part organizations
- ISO 16982:2002 Ergonomics of human-system interaction, Usability methods supporting human-centred design
- ISO/IEC 17024:2003 specifies requirements for a body certifying persons against specific requirements, including the development and maintenance of a certification scheme for personnel
- ISO/IEC 17025 General requirements for competence of test and calibration laboratories
- ISO/IEC 17799 Information technology: Code of practice for information security management
- ISO/IEC 17894 Ships and marine technology - Computer applications - General principles for development and use of PES in marine applications
- ISO 18000-7 Wireless standard for active RFID (Radio Frequency Identification)
- ISO/IEC 18004: QR Code Standardization
- ISO/IEC 18009: Information technology – Programming languages – Ada: Conformity assessment of a language processor (ACATS)
- ISO 18152:2003 Ergonomics of human-system interaction, Specification for the process assessment of human-system issues
- ISO 18185: Wireless standard for electronic seals using active RFID (Radio Frequency Identification)
- ISO 18245 standard concerning the assignment of Merchant Category Codes (MCC) in retail financial services
- ISO 18529:2000 Ergonomics of human-system interaction, Human-centred lifecycle process descriptions (available in English only)
- ISO 18629 standardized Process Specification Language (PSL).
- ISO 19005 PDF
- ISO 19011 standard providing guidelines for quality and environmental management systems auditing
- ISO 19092-1 Financial Services – Security – Part 1: Security framework
- ISO 19092-2 Financial Services – Security – Part 2: Message syntax and cryptographic requirements
- ISO 19101 Geographic Information: Reference model
- ISO 19105 Geographic Information: Conformance and testing
- ISO 19107 Geographic Information: Spatial schema
- ISO 19108 Geographic Information: Temporal schema
- ISO 19109 Geographic Information: Rules for Application Schema
- ISO 19110 Geographic Information: Feature cataloguing methodology
- ISO 19111 Geographic Information: Spatial referencing by coordinates
- ISO 19111 Geographic Information: Spatial referencing by identifier
- ISO 19113 Geographic Information: Quality principles
- ISO 19114 Geographic Information: Quality evaluation procedures
- ISO 19115 Geographic Information: Metadata
- ISO 19123 Geographic Information: Coverage schema
- ISO 19128 Geographic Information: Web Map Service
- ISO 19131 Geographic Information: Data product specification
- ISO 19136 Geographic Information: Geography Markup Language
- ISO/IEC 19501 Unified Modeling Language (UML)
- ISO/IEC 19502 Meta-Object Facility (MOF)
- ISO/IEC 19503 XML Metadata Interchange (XMI)
- ISO/IEC 19757 Document Schema Definition Languages (DSDL)
- ISO/IEC FDIC 19757-2 Regular-grammar-based validation RELAX NG
- ISO/IEC 19757-3 Rule-based validation – Schematron
- ISO/IEC 19790 Security requirements for cryptographic modules (see also FIPS 140)
ISO 20000–ISO 29999
- ISO/IEC 20000:2005 IT Service Management System (based on BS15000)
- ISO 20022 Financial Services - universal financial industry message scheme
- ISO/IEC TR 20943 Information technology - Procedures for achieving metadata registry content consistency
- ISO/IEC TR 20943-1:2003 Part 1: Data elements
- ISO/IEC TR 20943-3:2004 Part 3: Value domains
- ISO 22000 Food safety management systems -- Requirements for any organization in the food chain
- ISO/TS 22003 Food safety management systems -- Requirements for bodies providing audit and certification of food safety management systems
- ISO/IEC TR 22250 Regular Language description for XML – (RELAX)
- ISO/IEC TR 22250-1:2002 RELAX Core
- ISO/IEC 23270:2003 C# Programming Language
- ISO/IEC 23360 Linux Standard Base (LSB) core specification 3.1 (in publication as of 2005-12)
- ISO/IEC 23360-1 -- Part 1: Generic specification
- ISO/IEC 23360-2 -- Part 2: Specification for IA32 architecture
- ISO/IEC 23360-3 -- Part 3: Specification for IA64 architecture
- ISO/IEC 23360-4 -- Part 4: Specification for AMD64 architecture
- ISO/IEC 23360-5 -- Part 5: Specification for PPC32 architecture
- ISO/IEC 23360-6 -- Part 6: Specification for PPC64 architecture
- ISO/IEC 23360-7 -- Part 7: Specification for S390 architecture
- ISO/IEC 23360-8 -- Part 8: Specification for S390X architecture
- ISO 23950 Library standard ANSI/NISO Z39.50 - Protocol for searching and retrieving information, usually from bibliographic records
- ISO/IEC DIS 25961 Recommended Practice for Architectural Description of Software-Intensive Systems. See IEEE 1471
- ISO26000 Guideline about Social Responsibility also called ISO SR
- ISO/IEC 26300: OpenDocument Format (.odf)
- ISO/IEC 27001 Information technology -- Security techniques -- Information security management systems -- Requirements
ISO 30000–ISO 39999
- ISO 32000 - Portable Document Format.
See also
External links
- ISO Standards The complete list of all ISO published standards.
